Drone Accessories
0102030405
Operation Instruction of 7GHz3WTransmitter (VTX)
Product Dimension
Specifications
1. 7GHz 64CH: 6110MHz-7210MHz;
2. Max power: 3W (25mW, 1000mW, 3000mW, adjustable);
3. Input voltage: DC 7V-36V, supporting 2-8S battery input
4. Antenna connector: SMA Mother seat inner hole
5. Smart audio: IRC Tramp
6. Heat-dissipating method: aluminum alloy shell, heat sink&fan7. Hole spacing: 20mm*20mm/ø2mm
8. Dimension: 53mm*28.85mm*16mm
9. Weight: 25.85g
Function Introduction
1. Channel indicator: Red LED
2. Band indicator: Blue LED
3. Power indicator: Green LED
4. Band & Channel changer button
5. Power changer button
6. 1.0 6P Power connector
7. SMA Mother seat inner hole
Control Method and LED Indicator
1. Button ④ is the frequency point and frequency band switch button; eachshortpress of button ④ switches to the next frequency point, and the correspondingred LED flashes, in order: frequency points 1, 2, 3, 4, 5, 6, 7, and 8. Thisoperation can be repeated in a loop; see the figure belowfor details:
| Red LED | CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
| Flash once | Flash twice | Flash for 3 times | Flash for 4 times | Flash for 5 times | Flash for 6 times | Flash for 7 times | Flash for 8 times |
2. Long press button ④ to switch frequency bands. Long press for 5seconds and the corresponding blue LED will flash, in order: frequencygroups A, B, E, F, R, P, H, U. This operation can be repeated; see the figurebelow for details:
| Long press button ④ to switch bands | |||||||||
| Blue LED | Flash once | Flash twice | Flash for 3 times | Flash for 4 times | Flash for 5 times | Flash for 6 times | Flash for 7 times | Flash for 8 times | |
| A | B | E | F | R | P | H | U | ||
3. Button ⑤ is the power adjustment button. Each short press switches
the power by one level, cycling between the three levels of
25mW,1000mW, and 3000mW. The green LED is the power indicator
light, with the following states as shown in the figure below: 25mWflashes once, 1000mW flashes twice, and 3000mWflashes three times. Holding the button for 3 seconds enters pit mode, with the green light
staying on. See the figure below for details:
| Short press button ⑤ Power switch | ||||
| Green LED | Pit Mode | 25mw | 1000mw | 3000mw |
| Everlasting brightness | Flashes 1 time | Flashes twice | Flashes three times | |
. Frequency Table
| Frequency Table | ||||||||
| Channel Band | CH1 | CH2 | CH3 | CH4 | CH5 | CH6 | CH7 | CH8 |
| BAND A | 6110 | 6130 | 6150 | 6170 | 6190 | 6210 | 6230 | 6250 |
| BAND B | 6270 | 6290 | 6310 | 6330 | 6350 | 6370 | 6390 | 6410 |
| BAND E | 6430 | 6450 | 6470 | 6490 | 6510 | 6530 | 6550 | 6570 |
| BAND F | 6590 | 6610 | 6630 | 6650 | 6670 | 6690 | 6710 | 6730 |
| BAND R | 6750 | 6770 | 6790 | 6810 | 6830 | 6850 | 6870 | 6890 |
| BAND P | 6910 | 6930 | 6950 | 6970 | 6990 | 7010 | 7030 | 7050 |
| BAND H | 7070 | 7090 | 7110 | 7130 | 7150 | 7170 | 7190 | 7210 |
| BAND U | 6115 | 6265 | 6425 | 6585 | 6745 | 6905 | 7065 | 7185 |
Illustrate of 6P 1.0 Wiring
1. Channel indicator: Red LED
2. Band indicator: Blue LED
3. Power indicator: Green LED
4. Band & Channel changer button
5. Power changer button
6. 1.0 6P Power connector
7. SMA Mother seat inner hole
Notice for Use:
1. The VTX must be installed with space to ensure that the air convectionaround the module to ensure that the module heat dissipation; otherwise, the module overheating protection start, reduce the power to transmit, or
even shut down the power to transmit.
2. It is recommended that before turning on the power, to ensure that thecorrect voltage range, positive and negative poles are correct, so as not toburn components.
3. It is recommended that before turning on the power, make sure that theRF RF output has been installed antenna, which can extend the life of themodule.
4. Please read the instruction manual before use, so that you can correctlywire and extend the module service life.
2. It is recommended that before turning on the power, to ensure that thecorrect voltage range, positive and negative poles are correct, so as not toburn components.
3. It is recommended that before turning on the power, make sure that theRF RF output has been installed antenna, which can extend the life of themodule.
4. Please read the instruction manual before use, so that you can correctlywire and extend the module service life.